Marine Automation & Electrical System

DEIF Rudder angle transmitter RTA & RTC

DEIF Rudder angle transmitter RTA & RTC

Accurate, robust and frictionless are key attributes of DEIF’s rudder angle transmitters. Available in both CAN and analogue 2-wire versions, DEIF’s rudder angle transmitters allow for quick and simple installation and integration. The RTC and RTA transmitters are maintenance free with a continuous shaft rotation with no electromechanical moving parts, and are therefore not susceptible to the wear and tear associated with potentiometer type transmitters. Combined with an IP67 rating and a class accuracy of <0.25°, they are built to last in harsh environments. The cost and risk of system approvals can be reduced and mitigated by taking advantage of DEIF’s pre-approved MED systems which include our RTA and RTC transmitters combined with other products from DEIF’s bridge portfolio such as the XL, XDi, BW and BRW-2. Features Analogue. 2 wire 4 to 20 mA DC. Ø19mm stainless steel shaft for direct rudder connection. Available with 90 ° mounting bracket Directly compatible with DEIF’s RT-2 rudder angle transmitter. Suitable for rudder, azimuth and pitch angle “No touch” magnetic angle detection – no wear & tear Accuracy < 0.25 ° Analogue or CAN bus output for direct connection of one or more indicators Angle position range from +/- 20 ° to +/-180 ° Continuous shaft rotation Clockwise/counterclockwise, zero set & max./min. adjustment MED approved CAN with 16 bit resolution (+/-180 degrees = +/-32767) To receive a quote for Deif rudder angle transmitter, Kindly email us at sales@mariteksolutions.com Read More "DEIF Rudder angle transmitter RTA & RTC"

DEIF Wind sensor WSS 750

DEIF Wind sensor WSS 750

The DEIF ultrasonic WSS 750 wind sensor has an extended range. Like the WSS 550, it has no moving parts that could cause the wear-out problems typically associated with cup and vane type anemometers. This ensures consistent and reliable performance with no significant maintenance costs. Marine approved, with an IP67 rating, stainless steel construction and a separately powered heater to prevent icing, the WSS 750 is a extremely robust solution for harsh marine wind measuring applications such as Dynamic Positioning (DP) systems. The WSS 750 has been specially designed to make installation very simple with its bayonet mount. Easy installation and plug and play set up are also key factors when combining with DEIF’s XDi-N indicator which also comes with a comprehensive standard library of wind indicators to choose from. Using XDi-N indicators with the WSS 750 also allows integration with other navigation systems such as compass for true or geographical wind display and other systems such as VDR. Features Wind sensor, WSS 750 – features DEIF’s wind measuring devices from the WSS 750 series have a long list of features: Well-suited for dynamic positioning systems All stainless steel construction High power ultrasonic transducers in an equal sided triangle constellation No moving parts; no wear Wind speed up to 65 m/s (120 Knot) Speed accuracy better than 3 % (min. +/-0.2 m/s) Direction accuracy better than +/- 2° NMEA protocol IP66 and IP67 full waterproof DNV GL approved To receive a quote for Deif wind sensing system, Kindly email us at sales@mariteksolutions.com Read More "DEIF Wind sensor WSS 750"

DEIF Wind sensor WSS 550

DEIF Wind sensor WSS 550

DEIF’s ultrasonic WSS 550 wind sensor has no moving parts that could cause the wear-out problems typically associated with cup and vane type anemometers. This ensures consistent and reliable performance with no significant maintenance costs. Marine approved and with an IP66 enclosure and a built-in heater to prevent icing, the WSS 550 is a robust yet cost effective solution for marine wind measuring applications. The WSS 550 has been specially designed to make retrofit installation quick and simple when replacing DEIF’s older WSS/WSS-L products. Easy installation and plug and play set up are also key factors when combining with DEIF’s XDi-N indicator which also comes with a comprehensive standard library of wind indicators to choose from. Using XDi-N indicators with the WSS 550 also allows integration with other navigation systems such as compass for true or geographical wind display and other systems such as VDR. Features Wind measuring instrument – WSS 550 – features The wind measuring instrument from DEIF has a long list of features: Measures wind speed and direction IP66 housing Intelligent heating prevents icing up Working temperature down to -40 °C Well-proven and robust technology Advanced system integration with XDi-N Plug’n’play replacement for WSS/WSS-L Fully compatible with WSDI-2 indicators DNV GL approved To receive a quote for Deif wind sensing system, Kindly email us at sales@mariteksolutions.com Read More "DEIF Wind sensor WSS 550"

DEIF Advanced Genset Controller AGC 150

DEIF Advanced Genset Controller AGC 150

The Mains controller can synchronise 1 or 2 breakers (mains breaker and tie breaker) plus protect and monitor the utility in the DEIF power management system. Features AGC 150 Mains – features Operating modes with single or multiple mains:  AMF, Fixed power, Mains power export Load take over, Peak shaving Mains (Utility)   power monitoring (kW, kV, A & pf) decoupling protection kW export protection electrical protections No break transfer of load  Multi start settings Minimum of starting genset 12 Digital inputs and 12 digital outputs Communications ports (CAN, USB, RS485, Ethernet). Event & Alarm log (500 each) Programmable PLC editor To receive a quote for Deif Engine control system, Kindly email us at sales@mariteksolutions.com Read More "DEIF Advanced Genset Controller AGC 150"

DEIF Advanced Genset Controller AGC 150 BTB

DEIF Advanced Genset Controller AGC 150 BTB

The AGC 150 BTB controller can synchronise one breaker, protect and monitor the busbar. In total, DEIF’s power management system can handle eight bus tie breakers. AGC 150 BTB – features ►Automatic close of bus tie breaker if the system requests help  ►Manual control of bus tie breaker ►Section management ►12 Digital inputs and 12 digital outputs ►Communications ports (CAN, USB, RS485, Ethernet). ►Event & alarm log (500 each) ►Programmable PLC editor   To receive a quote for Deif Engine control system, Kindly email us at sales@mariteksolutions.com Read More "DEIF Advanced Genset Controller AGC 150 BTB"

SELCO SIGMA User Interface S6500

SELCO SIGMA User Interface S6500

The S6500 SIGMA User Interface SIGMA is an integrated generator protection and control system. The system is of high quality, is cost effective and easy to use. The S6500 fills the role of a flush mount digital multimeter as well as a configuration terminal. The S6500 will provide real-time readings of voltages, currents, active/reactive load, VA, frequency, etc. A single S6500 can support up to 16 S6000 and S6100 modules. The S6500 can be used to monitor and alter parameters in parallel with an operating SCADA system.   Features: ►Integrated Multimeter ►SIGMA User Interface ►SIGMA Remote Control ►C/B Status ►CAN Bus ►Pin Code Protected ►Redundant Supply To receive a quote for Selco generator control system, Kindly email us at sales@mariteksolutions.com Read More "SELCO SIGMA User Interface S6500"

SELCO SIGMA Power Management module S6610

SELCO SIGMA Power Management module S6610

The S6610 SIGMA Power Management Module SIGMA is an integrated generator protection and control system. The system is of high quality, is cost effective and easy to use. The S6610 PM Module provides power management functionality to the SIGMA system. In co-operation with the S6000 Input/ Output and Protection Module and S6100 Synchronizing/Load sharing Module. S6610 offers load depending start and stop, large consumer request and black out clearance functionality. It is also possible to program all SIGMA modules from S6610. Programming is PIN code protected.   Features: ►Full featured Power Manager ►Load depending start and stop ►5 large consumer requests ►5 non essential load trips ►Black out clearance ►2 Analogue outputs ►Automatic mode/ manoeuvre mode/manual mode ►Supports up to 16 generators ►Includes all functions of S6500 User Interface Module ►Redundant power supply To receive a quote for Selco generator control system, Kindly email us at sales@mariteksolutions.com Read More "SELCO SIGMA Power Management module S6610"

SELCO Generator Controller GC2000

SELCO Generator Controller GC2000

The GC2000 Generator Controller SELCO’s GC2000 provides efficient and reliable controls for gensets in a wide range of marine power applications, installed in commercial ships, tugboats, fishing vessels, crewboats, yachts and naval vessels etc. The GC 2000 features a complete engine-generator control and protection system, and includes an extensive range of functions for engine control & monitoring, synchronizing, load-sharing, load depending start and stop and complete generator protection. The GC2000 is designed to fit a wide range of applications, from basic genset control and monitoring applications to advanced and more complex power management solutions including combinations of shaft generators, bus tie breakers and shore power connections.   Features: ►Complete Generator control, monitoring and protection ►Automatic synchronisation and load sharing ►Embedded engine start/stop and alarm monitoring ►Power management including load-dependent start/stop schemes and blackout prevention/recovery ►Alternator control and protections ►Tie breaker control ►Non essential load tripping ►Load sharing redundancy and heavy consumer management ►LCD screen to display engine and generator values and alarms ►RS-485/CAN ports with Modbus RTU/TCP communication ►CAN bus dedicated for J1939, CANopen and I/O extensions ►Easy configurable via front panel or via a PC and internal configuration software ►Event logging ►SD card support   To receive a quote for Selco generator control system, Kindly email us at sales@mariteksolutions.com Read More "SELCO Generator Controller GC2000"

SELCO Tacho Detector M0500

SELCO Tacho Detector M0500

The M0500 Tacho Detector The SELCO M0500 is an accessory unit for the SELCO M2000 Engine Controller and the M2100 Emergency Controller. The speed output signal is typically used in conjunction with the SELCO M2000 or M2100. This signal is used by the M2000/M2100 to provide crank disconnect at 33% of nominal speed and over speed alarm (and optional engine shutdown) at 115% of nominal speed. The M0500 also includes an output which tells the M2100 Emergency Controller whether or not the generator output voltage is within the nominal range.   Features: ►Reads engine speed from AC voltage ►Tacho system for M2000 and M2100 ►Square wave speed output ►Nominal voltage output   To receive a quote for Selco Engine control system, Kindly email us at sales@mariteksolutions.com Read More "SELCO Tacho Detector M0500"

SELCO Shut-down M0600 Unit

SELCO Shut-down M0600 Unit

The M06000 Shut-down Unit The unit has inputs for over speed, low oil pressure and a user defined input which can be used to monitor e.g. high water temperature. The M0600 has an input to indicate that the engine is running and another input to indicate that the engine is in the process of being halted. An output relay will give a closing signal, which can be used to stop the engine via the fuel valve or the stop solonoid (if available). The M0600 will work as a stand-alone protection unit for DIN-rail mounting. Alternatively, when limited space is available, the M0600 can be mounted directly on the rear side of the M2000 Engine Controller.   Features: ►Stand alone engine protection ►Provides complete redundancy in combination with M2000 ►Can be mounted on the rear side of the M2000 ►Complies with even the strictest Marine Classification requirements   To receive a quote for Selco Engine control system, Kindly email us at sales@mariteksolutions.com Read More "SELCO Shut-down M0600 Unit"

Go to top